Electrochemical modification is to change the electrical and chemical properties of activated carbon surface by using micro electric field, so as to improve the adsorption selectivity and performance.It does not need to add chemical agents, does not need to heat, does not cause pollution to the environment, low energy consumption, only a few hundred millivolts, easy to operate.The results show that the adsorption equilibrium of activated carbon is dependent on the electric potential: the adsorption amount of activated carbon increases with the increase of the potential, and the adsorption speed is accelerated;Arpolarity polarization is beneficial to the adsorption of chloroform by activated carbon, while cathodic polarization inhibits the adsorption of chloroform by activated carbon 3-341]. Activated carbon heteroatom carrier and compound modificationActivated carbon has very high stability and good activity, these two basic properties become the activated carbon as a catalyst or catalyst carrier conditions.By introducing certain heteroatoms and compounds on the surface of activated carbon by liquid phase deposition, the adsorption performance of activated carbon can be increased by using the binding effect between these substances and adsorbents.compounds, which has the advantages of increasing the reaction rate and increasing the adsorption capacity.Yang Quanhong et al. 'Using FESO;Activated carbon material was modified.coconut shell activated carbon price
The experimental results show that the surface structure of the activated carbon material modified by FeSO changes: the specific surface area decreases, the surface oxygen content increases, the plane of the random layer graphite carbon net is destroyed to a certain extent, and the ammonia absorption capacity and benzene absorption performance of the sample are greatly enhanced.He ChunHong et al. [reported the research progress of supporting activated carbon materials in the removal of SO; the removal ability of SO was significantly enhanced after supporting Co, Ni, Mg, and V compounds, which was due to the formation of Co(OH)2, Ni(OH)2, Mg (OH)2, and V,0 microcrystals on the surface of activated carbon after supporting, which enhanced the desulfurization activity of activated carbon.Microwave heating can produce good effects in the preparation and modification of activated carbon (S2. Microwave modification, many backwater hole is opened, the distributed capacitance change obviously, promoting the improvement of the adsorption. The microwave power and irradiation time are key determinants of modified activated carbon adsorption performance. On the mechanism of microwave carbonization and activation, it is generally believed thatactivated carbon china manufacturers
Plant waste is mostly made of plant fiber raw materials, in the plant body under the action of capillary, modified solution absorbed by material whole fully, between fiber is filled with the subtle space, make the dry material volume expansion after soaking wet, and reaction. Because of the water in the raw material, modified solution constitute a polar molecule, with a strong absorption of microwave dielectric properties,Therefore, polar molecules collide and rub violently with microwave frequency, generating a large amount of heat, which makes water and modified solution volatilize rapidly, and generate steam pressure, which explodes out from the inside of the raw material to the outside. This sharp action makes the fiber space of the raw material expand and produce sharp drying.In this way, the raw material has a more obvious pore structure and a larger internal specific surface area than before microwave irradiation. Compared with the traditional heating method, the mechanism of microwave in the preparation process of activated carbon is completely different.It shows its unique advantages: high efficiency, energy saving, uniformity, selectivity, low pollution, high thermal efficiency, low energy consumption, simple process and equipment and small footprint, conducive to automation, low carbon loss, and recovery of useful substances.Activated carbon, is black powder or block, granular, honeycomb amorphous carbon, but also a regular arrangement of crystalline carbon.In addition to carbon elements, activated carbon also contains two kinds of admixtures: one is the chemical combination of elements, mainly oxygen and hydrogen, these elements are due to incomplete carbonization and residual in the carbon, or in the activation process, foreign non-carbon elements and activated carbon surface chemical combination;Another kind of admixture is ash, which is the inorganic part of activated carbon, and ash in active carbon is easy to cause secondary pollution.Because of its strong adsorption, activated carbon is widely used in production,In the life.Activated carbon material is processed by the amorphous carbon, has a large specific surface area, the gas, solution of inorganic or organic matter and colloidal particles have good adsorption capacity.Activated Carbon materials mainly include Activated Carbon (AC) and Activated Carbon Fibers (ACF), etc.Activated carbon material as a kind of excellent adsorbent, mainly because of its unique adsorption surface structure and surface chemical properties.Activated carbon material has stable chemical properties and high mechanical strength.