The experimental results show that the surface structure of the activated carbon material modified by FeSO changes: the specific surface area decreases, the surface oxygen content increases, the plane of the random layer graphite carbon net is destroyed to a certain extent, and the ammonia absorption capacity and benzene absorption performance of the sample are greatly enhanced.He ChunHong et al. [reported the research progress of supporting activated carbon materials in the removal of SO; the removal ability of SO was significantly enhanced after supporting Co, Ni, Mg, and V compounds, which was due to the formation of Co(OH)2, Ni(OH)2, Mg (OH)2, and V,0 microcrystals on the surface of activated carbon after supporting, which enhanced the desulfurization activity of activated carbon.Acid-base modification is to use acid, alkali and other substances to treat activated carbon, according to the actual need to adjust the surface functional groups of activated carbon, make it change, improve its ability of adsorption of metal ions, so as to achieve the desired adsorption effect.Acid-base modification of activated carbon is usually carried out to improve the adsorption effect of activated carbon on metal ions represented by copper ions. The commonly used modifiers include HC1, NaOH and citrate 3.It was found that by acid-base modification of common coal activated carbon, the ash content of the activated carbon could be greatly reduced and the specific surface area of the activated carbon could be increasedactivated charcoal pellets wholesale
Electrochemical modification is to change the electrical and chemical properties of activated carbon surface by using micro electric field, so as to improve the adsorption selectivity and performance.It does not need to add chemical agents, does not need to heat, does not cause pollution to the environment, low energy consumption, only a few hundred millivolts, easy to operate.The results show that the adsorption equilibrium of activated carbon is dependent on the electric potential: the adsorption amount of activated carbon increases with the increase of the potential, and the adsorption speed is accelerated;Arpolarity polarization is beneficial to the adsorption of chloroform by activated carbon, while cathodic polarization inhibits the adsorption of chloroform by activated carbon 3-341]. Activated carbon heteroatom carrier and compound modificationActivated carbon has very high stability and good activity, these two basic properties become the activated carbon as a catalyst or catalyst carrier conditions.By introducing certain heteroatoms and compounds on the surface of activated carbon by liquid phase deposition, the adsorption performance of activated carbon Air velocity of empty tower :U= 1.0m /s.OriginalIts adsorption performance mainly depends on several main material parameters and process parameters on it [8. Material parameters including carbon adsorption porosity, thickness of honeycomb structure and the content of carbon; process parameters including fluid flow rate and concentration of the adsorption properties of adsorption, can adsorption depends on the carbon structure and adsorption properties of features such as molecular weight). The curve is one of the main performance characterization of adsorption, adsorption is the adsorbate concentration ratio before and after the change over time of a function [9 '. This ratio is 0.95, the amount of adsorption properties of adsorption is called penetration capacity. Penetration capacity depending on the fluid flow rate, the concentration of the adsorbate and honeycomb carbon component content
Factors such as [10. For honeycomb activated carbon, the wall thickness is a very important parameter, by changing the wall thickness to improve its adsorption efficiency. Under the same porosity, thickness increases, the honeycomb carbon content per unit volume also will increase, which can improve the adsorption capacity. This is because the wall thickness increases, the fluid channel in the cellular cross-sectional area reduced, so the real surface or volume flow rate will increase. At the same time, the contact between adsorbate and carbon efficiency will, there is a balance between the two. Under the given conditions, the balance will determine adsorption increase or decrease. If the adsorbate at higher the diffusion rate diffuses to the inside of the honeycomb wall, and the empty adsorption site can be continuously adsorbed, so the thick-walled honeycomb should have better adsorption efficiency and adsorption capacity"Determination of air velocity and cross-sectional area of empty towerThe empty tower gas velocity is the velocity of gas passing through the entire cross section of the adsorber.The selection of air velocity not only directly determines the size and pressure drop of the adsorber, but also affects the adsorption efficiency.
https://www.wyactivatedcarbon.com/